Difference between revisions of "Membership Knowledge Base"

From ATXHackerspace

Jump to: navigation, search
(Red)
Line 10: Line 10:
  
  
'''Maintenance plan'''
 
  
* We will have several qualified people learn the repair so that there are more people capable of maintaining the machine.
 
* We will train more people up on how to safely re-home and focus the lenses.
 
* We will post contact info for those volunteers for potentially faster response.
 
* If we find that any parts need ordering, we will add those to the list of spares we keep on hand; in February’s maintenance push we ordered doubles of belts and such. If the problem is that simple there should be minimal delay.
 
  
 +
FAQ
  
 +
'''Z-height is visibly off, and at some point in its range the motor sound changes and it doesn’t move'''
  
 +
This is almost ENTIRELY due to debris getting into the thin gap at the rear of the bed/airbox area.  it needs to be lowered slightly and have the debris removed from the gap, then rehomed.  I've rehomed the unit before, it would certainly be a good idea to have a few regulars at the space available for this since it happens a lot.  the best way to prevent it is to make sure you clean out the bed and make sure small bits aren't blown off the back of the bed when you're done, also inspect that are before you start moving the bed.  Matt
  
  
FAQ
 
  
'''Problem that might indicate an alignment issue'''  
+
''''Insufficient flow from air', WTF?'''  
  
Stop using it entirely and contact someone with deep experience. Running the laser at full power when misaligned can turn a simple adjustment of lenses into an expensive and time-consuming problem.
+
Turn on the air.
  
''''Insufficient flow from air', WTF?'''
 
Turn on the air.
 
  
 
'''Display indicates computer crashed'''
 
'''Display indicates computer crashed'''
Bounce the system by resetting the breakers on the bottom left in the back. Pester Danny for a power supply & spare.
+
 
 +
Bounce the system by resetting the breakers on the bottom left in the back. Pester Danny for a low voltage power supply & spare like the Meanwell Rob already got.
 +
 
  
 
'''Manual jogging'''
 
'''Manual jogging'''
 +
 
I have a project that has alignment marks on them and wondering if there is a way on the Red laser to move the laser head manually either by the arrows or coordinates so I can check my overlay?
 
I have a project that has alignment marks on them and wondering if there is a way on the Red laser to move the laser head manually either by the arrows or coordinates so I can check my overlay?
  

Revision as of 20:45, 3 May 2019

Volunteer your skills/knowledge here


Editing Wiki

'Request account' from main page & email martinbogo@gmail.com

Red

Report all problems to facilities@atxhs.org (Danny)



FAQ

Z-height is visibly off, and at some point in its range the motor sound changes and it doesn’t move

This is almost ENTIRELY due to debris getting into the thin gap at the rear of the bed/airbox area. it needs to be lowered slightly and have the debris removed from the gap, then rehomed. I've rehomed the unit before, it would certainly be a good idea to have a few regulars at the space available for this since it happens a lot. the best way to prevent it is to make sure you clean out the bed and make sure small bits aren't blown off the back of the bed when you're done, also inspect that are before you start moving the bed. Matt


'Insufficient flow from air', WTF?

Turn on the air.


Display indicates computer crashed

Bounce the system by resetting the breakers on the bottom left in the back. Pester Danny for a low voltage power supply & spare like the Meanwell Rob already got.


Manual jogging

I have a project that has alignment marks on them and wondering if there is a way on the Red laser to move the laser head manually either by the arrows or coordinates so I can check my overlay?

There’s no way to position Red. You can do that with Blue. I do alignment in one of two ways: 1) by laying a sheet of paper on the bed and slicing it with 90% speed. 2) by cutting out a frame jig before hand.

The jig or paper lets me know where to put the item I’m cutting. If I need ~2mm precision, the paper works. Less than that, take the time to build the jig.

Danny's CNC router

Report all problems to dannym@austin.rr.com


FAQ

Cleaning Clean the ways, wheels, & leadscrew & re-lube weekly. Z jitter can be caused by debris in the ways. If not that, it can be a worn lead nut.


Sparktech eBay name drillman1, carbide plus store

Wood

FAQ

Clean the machines weekly to avoid problems with dust blockage & friction

Sawstop cleaning The Sawstop tilt & height can get jammed. It can be cleaned from the access door on the side. Depending on where it is jammed, it may require reaching in & cleaning it by hand.

Miter Saw cleaning Turn off the saw, start the dust collector, reach back & pull the debris blocking the dust.

Bugs We should rework the station a bit: add lights; fiberglass a cowl that accounts for the angle of slip; add a better debris guard in the design; add a pencil holder; add a tape measure cubby. Joe


Small routers These are working but in disuse. They are a good place to learn CNC; fire one up & go for it!

Metal

Joe josephqtn1@gmail.com

Manual Mills Joe
Lathe Jay
Tormach Mill Eric, Max


Electronics

See ../Groups/DIY Electronics for more information

Casting

Eric aluminum Matthew Goodman


Software/Hardware

  • Python: Gunnar likes to hold classes regularly on data science & robotics topics
  • CAD Drafting and 3D modeling Eric
  • Openscad Rob
  • Arduino Bion, Ryan, Marshall Vaughan
  • Beagle Ryan, Jerry
  • FPGA/steppers Danny
  • Brushless commutation Jerry
  • SQL Crothers
  • GL/gaming Steve Baker
  • Web Steve Baker
  • Get bitched out Jay

Art